ECE R43 PDF

May 4, 2019 posted by

E/ECE/ Rev.1/Add/Rev.2 E/ECE/TRANS/ Regulation No. 43 page 4 CONTENTS (continued) Annex 3 Annex 4 Annex 5 Annex 6 Annex 7 Annex 8. Mr. Masaru Morikawa, General Safety Subcommittee, JASIC. – Safety Glass Testing according to ECE R Mr. Pham Minh Thanh. E/ECE/TRANS/) November 2, STATUS OF UNITED NATIONS REGULATION ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL.

Author: Sajar Vomi
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Travel
Published (Last): 20 August 2011
Pages: 20
PDF File Size: 5.23 Mb
ePub File Size: 1.87 Mb
ISBN: 111-5-28572-490-2
Downloads: 94427
Price: Free* [*Free Regsitration Required]
Uploader: Tonris

The impact surface of the felt cover shall be replaced after 12 tests.

The test for resistance to radiation shall be deemed to have given a positive result if the following conditions are fulfilled: Interpretation of Results For a test piece or sample to be considered flexible its vertical deflection shall be more than 50mm after 60s. The abrasion test in accordance with the requirements of Annex 14, Paragraph 6. A set of test pieces or samples submitted for approval shall be considered satisfactory from the point of view of the resistance to simulated weathering if all test pieces have given a satisfactory result.

The average of the measured values for the three ASS hard-coated polycarbonate reference samples per cycles number is used to calculate a correction factor per cycles number for exactly this wheel pair reference Paragraph 4.

Automotive Glass Testing in Compliance with ECE R43 | WO | TÜV Rheinland

Secondary image separation test in accordance with the requirements of Annex 3, Paragraph 9. Test of Resistance to Simulated Weathering 6. The ball shall be allowed to make only one impact. Get in contact with us!

  ANWAR SADAT AUTOBIOGRAPHY PDF

ECE R 43 DOT Approvals

Resistance-to-humidity test in accordance with the requirements of Annex 9, G43 3. The sample box shall be placed into the stainless steel tray and fixed using adhesive tape on the two short sides of the box according to Figure B.

When not in use, the abrasive wheels shall be stored in the same conditions of temperature and humidity. If the requirements given in Paragraph 3. Dimensions are given in Figure The cross-cut test shall be considered to have given a satisfactory result if at least the cross-cut value Gt1 is met.

All glazing materials, including glazing material for the manufacture of windscreens, shall be such that, in the event of shattering, the danger of bodily injury is reduced as ecs as possible.

A light trap shall be provided that will absorb the beam completely when no test piece is present, or the instrument design shall obviate the need for a light trap.

Nature and type of surface coating: The height of drop for the various nominal thickness values is given in the table below: Normal thickness of glass: Using a soft bristle, anti-static brush, lightly brush off any debris adhered to the surface of the test pieces or alternatively rinse the test pieces with distilled, deionized or demineralised water. Other exposure conditions shall be as follows: The maximum secondary-image separation shall be measured. Indices of difficulty and test method The requirements of Annex 3, Paragraph Test of Resistance to Abrasion The purpose of this test is to determine whether the resistance of a safety glazing to abrasion exceeds a specified value.

  CONVERT OMNIFORM TO PDF

The incorporation or otherwise of conductors.

VW T25 Opening Quarter Light Glass LHS Ece-r43 E37 C9065

The chemicals shall be applied to the side of the test piece which represents the outside face of the windscreen or safety glazing pane when mounted on the vehicle while this side is under tensile stress.

Indices of Difficulty of the Secondary Characteristics Colourless Tinted Colouring of glass 2 1 Colouring of interlayer 1 2 The other secondary characteristics are cee involved. Optical distortion at a Point M: Examples of our work.

To minimize the temperature change of the test piece, the test ecce be performed within 30s of the removal of the test piece from the conditioning appliance.

Benefits at a Glance. Report this difference for 10 washing operations 10 double strokes for the outside surface of the test samples. R3 Rigid Plastic Panes 2. During a cycle of min the test pieces are exposed to light without water spray for min, and to light with water spray for 18min.

Test Under Load 9. The light transmittance measured according to Annex 3, Paragraph 9. If the flame does not reach the last measuring point, measure the burnt distance up to the point where the flame was extinguished.